Reinitialize your Holosun EPS Carry Red Dot Sight

Occasionally, you may need to restore your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the settings or are experiencing unexpected behavior. Fortunately, resetting your Holosun is a easy process that can be performed in just a few actions.

First ensuring your red dot sight is turned on.
Find the small button for reset on the side of the device.
Utilize a thin tool to activate the reset button for approximately 7 moments.
Release the switch and your Holosun EPS Carry Red Dot sight will power cycle.
Its red dot sight should now be set back to its factory settings.

Reset Your Holosun EPS Carry Red Dot back to Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to go back to basics, resetting it back to standard configuration is a breeze. First, determine the tiny button on the bottom of your optic. Then, sustain it for around twelve seconds until you see a brief flash. Your Holosun EPS Carry is now returned to its factory settings, ready for precise aiming.

revive your Holosun EPS Carry Back to Life

Is your beloved Holosun EPS Carry experiencing some glitches? Don't despair! A simple factory reset can often resolve the problem and get your red dot sight back to its former glory. Before you begin, remember to remove the battery from your Holosun EPS Carry to prevent accidental activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these easy steps:

Simultaneously press and hold the power button for approximately 5 seconds.
A message will flash, indicating that the reset is being performed.
Let go of the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can insert the battery and verify your sight's functionality. If you encounter any further problems, don't hesitate to contactsupport team.

Return Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Follow these steps carefully to ensure a successful factory reset.

Beginning with, Turn on your Holosun EPS Carry by pressing the power button.
Next, press and hold both the mode button and the up/down adjustment button simultaneously.
While continue holding these buttons, tap the power button once.
You will show a confirmation prompt indicating that the reset process is initiated.
Allow the process to complete. This may take a few moments. Once done, your Holosun EPS Carry will automatically shutdown.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Reset All Settings on Your Holosun EPS Carry

To Factory reset your Holosun EPS Carry sight, you'll here need to access the settings menu. This can usually be done by Pressing a specific button combination. Consult your Guidebook for the exact button sequence for your model. Once in the settings menu, look for an option that says "Reset All". Select this option and confirm the reset. Your sight will then power off and restart with all settings Restored to their default values.

Reinitialize your Holosun EPS Carry with a Factory Original Settings

If your Holosun EPS Carry is acting erratically, a factory reset might be the solution. This will set back your sight to its initial settings, clearing any custom configurations you've made. To perform this reset, follow these straightforward steps:

Initially, find the reset switch on your EPS Carry.
Secondly, press a small object, like a pen tip, to depress the reset switch.
While keep the reset switch pressed, turn your EPS Carry.
You'll blink a message indicating that the reset is successful.

Once the reset is complete, your EPS Carry will be returned to its factory settings.